To make this project come alive, there are a few necessary items before you can begin.
1. You'll need "Magical Decal Coating Paper" - found here.
2. SLOM Jars - cheapest at IKEA
2. SLOM Jars - cheapest at IKEA
GATHER YOUR SUPPLIES
1. Images to transfer
Use anything you like. I made up my canister labels in Photoshop. I wanted them to be a bit different and quite typographic so decided to style them based on dictionary definitions (my artwork is attached as a free printable if you would like to use them!)
2. Inkjet printer
3. Decal Paper (blue watermark on back)
Decal paper comes in clear or white. I'm using the clear paper because I want a transparent background around my image.
4. Magic Paper (attached translucent protective paper)
5. Laminator
Basic laminators can be bought for around $20 from most office supply and department stores.
6. Scissors
7. Water
8. Soft cloth
9. Item to embellish
As already mentioned, I'm using my plain SLOM jars from IKEA.
10. Microwave, oven or hairdryer
1. Print your image onto the glossy side of your decal paper (DO NOT mirror your image) using an inkjet printer. Allow to dry thoroughly. I created my canister labels in Photoshop and have attached them below as a free printable if you would like to use them.
2. Separate the translucent protective paper from the magic paper. Do not throw the translucent paper away.
3. Place the magic paper gloss side up on your table. Lay the decal paper printed side down on top of the magic paper. Place the translucent protective paper gloss side down on top of the decal paper.
As my image took up the entire sheet of decal paper I did not need to trim around it first. If you are working with a smaller image you may wish to cut roughly around it with scissors.
4. Laminate your stack of three papers together on low speed and at low temperature.
Basic laminators can be bought for around $20 from most office supply and department stores.
5. Discard the translucent paper. Your decal paper and magic paper should now be fused together. Trim closely around your image - you can see it quite easily through the paper if you hold it up to the light.
Where there is no ink, the decal will leave a very fine, slightly translucent film which is visible close up or on certain angles. As my image is text alone with no border I experimented with techniques and found the neatest finish to be a nice even box (trying to mimic the outline of the text just looked messy). If your image has a distinct border then trim approximately 2mm all the way around it (leaving a small buffer ensures you get a good seal).
Basic laminators can be bought for around $20 from most office supply and department stores.
5. Discard the translucent paper. Your decal paper and magic paper should now be fused together. Trim closely around your image - you can see it quite easily through the paper if you hold it up to the light.
Where there is no ink, the decal will leave a very fine, slightly translucent film which is visible close up or on certain angles. As my image is text alone with no border I experimented with techniques and found the neatest finish to be a nice even box (trying to mimic the outline of the text just looked messy). If your image has a distinct border then trim approximately 2mm all the way around it (leaving a small buffer ensures you get a good seal).
6. Dampen the back of the decal paper (watermarked side) with a cloth until it becomes translucent. Wait around 15 seconds then gently peel the paper away completely.
Important: ensure you remove the watermarked decal paper only at this stage.
7. Quickly immerse the decal in a shallow dish of water to dampen the other side then position it, image side down, on your item, smoothing it down with your fingers and a slightly damp cloth to remove excess water.
8. Carefully slide off the backing paper and manipulate the decal into its exact position then continue to smooth it until it is water and air bubble free (the image for step eight shows the transfer with some minor creases and bubbles. This is only because the photograph depicts the removal of the backing paper before I have smoothed the decal. Rest assured that it does flatten out completely).
9. Finally, set the decal by either:
- Baking in an electric oven for 8 minutes at 150 degrees celsius
- Cooking in a microwave for 5 minutes on low
- Blowing with a hairdryer for 5 - 10 minutes
Important: ensure you remove the watermarked decal paper only at this stage.
7. Quickly immerse the decal in a shallow dish of water to dampen the other side then position it, image side down, on your item, smoothing it down with your fingers and a slightly damp cloth to remove excess water.
8. Carefully slide off the backing paper and manipulate the decal into its exact position then continue to smooth it until it is water and air bubble free (the image for step eight shows the transfer with some minor creases and bubbles. This is only because the photograph depicts the removal of the backing paper before I have smoothed the decal. Rest assured that it does flatten out completely).
9. Finally, set the decal by either:
- Baking in an electric oven for 8 minutes at 150 degrees celsius
- Cooking in a microwave for 5 minutes on low
- Blowing with a hairdryer for 5 - 10 minutes
10. Enjoy and marvel at your DIY accomplishment!!
0 comments:
Post a Comment